The Smart Home Journal

Expert tips, ideas, and advice for creating a smarter, cleaner, better-connected home in NYC.

How to hide TV wires in a plaster wall: recessed TV with no visible cables in a Manhattan apartment

How to Hide TV Wires in a Plaster or Concrete Wall (Without Wrecking It)

November 03, 2026•10 min read

There are four real ways to hide TV wires in a plaster or concrete wall. One: an in-wall power and cable kit, but only where the wall is hollow behind the plaster. Two: a recessed outlet and conduit put in by a licensed pro. Three: a channel cut into the wall and re-plastered. Four: a paintable cable raceway or furniture and millwork that covers the cables. Never push a TV power cord or a power strip inside a wall. The electrical code does not allow it. In New York apartments, expect holes. A certified installer makes the right ones, and a painter or plasterer closes them.

⚡ QUICK SUMMARY

Plaster over metal lath and poured concrete are the two hardest TV walls in New York. Hollow plaster wall: in-wall power kit, fish cables (HDMI cables, ethernet) through the cavity, holes at top and bottom, then patch and paint. Solid brick or concrete wall: a cable raceway painted to match, furniture or millwork that hides a surface chase, or a shallow channel cut and re-plastered. Any wall: the TV power cord never goes inside the wall (NEC Article 400). National cost for a mount with wires hidden runs $155 to $355 in labor before in-wall work; NYC runs higher. Wire fishing almost always means holes, and we do not patch or paint.

The wall mounted TV is up. The TV cables are hanging under it like spaghetti: HDMI cables, the power cord, maybe a surge protector on the floor. In a drywall house, an installer fixes that in a couple of hours. In a pre-war apartment with plaster and metal lath, the same job needs a plan. So does a post-war tower with concrete walls. You need the right tools and honest expectations about holes. Here is how we do it, what it costs, and what not to do.

Home Theater Advisors has mounted TVs and hidden the cables in New York City apartments since 2011, with over 500 installs. Every audio-video system we install is wire-free on the outside. That promise gets tested on plaster and concrete every week, so this guide comes from the walls, not a manual.

Why a Plaster, Brick or Concrete Wall Is Different for a Wall Mounted TV

Plaster over lath (pre-war). Behind the smooth surface is a layer of wood strips or metal mesh, then a hollow cavity, then the studs or the brick. The plaster cracks if you cut it wrong. The metal lath dulls bits and snags fish tape. But there is usually a cavity, which means you might be able to fish cables inside the wall.

Poured concrete (post-war). Many towers built from the 1950s on have solid concrete walls and slab floors, sometimes with a thin layer of furring and drywall over them. There is no cavity. Cables cannot travel inside the wall because there is no inside. Everything has to go on the surface in a raceway or behind furniture, or into a channel cut into the masonry. A brick wall in a loft behaves the same way.

Modern construction. Metal studs behind drywall are the easiest case, but glass partitions, stone feature walls, and tile stop the wire cold. Never assume. Tap the wall, use a scanner, and if needed make a small test hole where the TV will cover it.

Rule One: The Power Cord (and Power Strip) Never Goes in the Wall

A TV power cord is a flexible cord. The National Electrical Code (Article 400) does not allow flexible cords to run through walls, ceilings, or floors. Low voltage cables like HDMI cables, ethernet, and speaker wire are allowed in the wall if they carry an in-wall rating (CL2 or CL3). A power strip or surge protector is a flexible cord too, so it stays outside the wall. So the power needs one of two fixes.

Two code-friendly ways to get power behind the TV

✓

In-wall power kit - A kit like PowerBridge or Legrand puts a new outlet behind the TV and an inlet near the old outlet. In-wall rated cable joins them inside the wall. The kit itself does not need an electrician. Per the PowerBridge FAQ, it only works in standard stud-framed hollow walls. Not concrete.

✓

Recessed outlet by a licensed electrician - An electrician adds a recessed box behind the TV, fed from a nearby circuit. This is the cleanest fix for concrete and drywall. In concrete, the run goes in a surface chase or a cut channel. In drywall, the wiring goes inside the wall just like low voltage wire. It is also the fix for any wall when you want it done once.

⚠️ Do Not Do This

Extension cords, a power strip, or a surge protector inside a wall are a fire risk and a lease or co-op violation. If a handyman offers to "just tuck the cord in the wall," say no.

A recessed TV on a feature wall in a Manhattan apartment. No visible wires.

A recessed TV on a feature wall in a Manhattan apartment. No visible wires.

How to Hide TV Wires in a Plaster Wall: Fish Cables Through the Cavity

1Find what is behind the plaster

A scanner locates studs and metal lath. A small test hole behind the future TV position confirms the cavity depth and whether there is brick, blocking, or old wiring in the way.

2Cut two openings, not a slot

One behind the TV and one near the floor outlet or the equipment cabinet. Use a multi-tool with a carbide blade for plaster and metal lath. Score the plaster first to stop cracks from spreading.

3Fish cables through the cavity

HDMI cables, ethernet, and speaker wire go through the cavity from one opening to the other. Lath snags fish tape, so this is where experience saves the wall. Leave a pull string for the future.

4Install the in-wall power kit

Outlet plate behind the TV, inlet plate below. The kit's in-wall cable travels the same path as the low voltage cables. Plug the inlet into the existing outlet with the short cord that ships with the kit.

5Mount, connect, and hide the plates

The wall mounted TV covers the upper opening. The lower plate sits behind furniture or the media cabinet. What is left is a TV on a wall and nothing else. No cable clips, no raceways, no visible cables.

6Patch and paint

Cut plaster needs a plasterer or painter to finish the edges around the plates. We do not patch or paint. Line up your painter for the day after the install.

💡 Pro Tip: Leave a Conduit Behind

Run an empty 1.5 inch flexible conduit between the two openings while the wall is open. The next time an HDMI standard changes, the new cable pulls through in five minutes with no new holes. If you are in a full renovation, read our list of the 9 wires to run before the walls close.

How to Hide TV Cables on a Concrete Wall: Cable Raceway, Millwork, or a Channel

A solid wall gives you four paths. None of them involve fishing cables, because there is nowhere to fish them.

Millwork, furniture, or a shallow feature wall

Build a cabinet, a panel, or a 2 to 3 inch furred wall in front of the masonry. Cables, a recessed outlet, and even a soundbar disappear inside it. This is the premium result and the one you see in most of our project photos.

Paintable cable raceway

A flat plastic or metal channel screwed to the wall, painted to match. It carries the HDMI cables and power cord from the TV down to the outlet. Cable raceways are not invisible up close, but they look clean from across the room and they are the cheapest option. Good raceways come in white and paintable finishes.

Cut a channel (chase) in the masonry

A specialist saws a shallow channel, sets conduit, and a plasterer fills it flush. Dusty, loud, and often restricted by the building. Best done during a renovation, not on a Tuesday afternoon.

Move the TV to the outlet

Sometimes the smart fix is to mount the TV right above an outlet that is already there. Use a slim mount and a short cable cover or cable clips behind the furniture. No drilling for power, almost no visible cable.

Not sure what your wall is made of? We will look, tap, and tell you the right approach, free.

Book a Free Consultation

What Does It Cost to Hide TV Cables and HDMI Cables?

ItemTypical PriceSource
TV mounting, professional labor (national)$155 - $355LatestCost, 2026
In-wall power and cable kit (material)$60 - $150Retail list, 2026
Paintable cable raceway kit (material)$15 - $60Retail list, 2026
Home theater wiring (national average)$700 - $2,900 (avg $1,400)HomeAdvisor, 2025
Recessed outlet by a licensed proVaries by building and circuit; get a quoteLocal electrician
Custom millwork TV wallPriced per project by the millworkerLocal millwork shop

These are national averages. New York City labor, building rules, and plaster or concrete walls push costs higher. We charge MSRP on any equipment we supply. You get an itemized proposal before work starts.

Building Rules That Change the Job

Check before anyone drills

✓

Work hours and noise - Most co-ops and condos limit drilling to weekday hours. Concrete work is loud. Schedule around the building, not around the game.

✓

Insurance and licenses - Most buildings want proof of insurance from any contractor. Electrical work in New York City needs a licensed pro, and a certified installer for the mount and cables is worth it.

✓

Shared walls - A solid wall between you and a neighbor is theirs too. Deep channels may need board approval. Millwork in front of the wall avoids the question.

✓

Fire stopping - Openings between units or floors must be sealed with fire-rated material. A professional installer knows the rule; a handyman may not.

What Goes Wrong When It Is Done Badly

Cracked plaster that spreads a foot past the opening. A power cord melted inside a wall. A wall mounted TV screwed into lath instead of studs that sags in a month. A cable raceway that was never painted. Cable clips in a crooked line down the wall. We get called to fix all of these. The fix costs more than doing it right the first time, and it always comes with new holes.

“I spent years watching great products get installed badly. The equipment matters - but the installer matters more.”

- Mark Feinberg, Founder of Home Theater Advisors

Common Questions About Hiding TV Cables (Surge Protector, Power Strip, Raceways)

Can you run a TV power cord or power strip inside the wall?

No. Flexible cords, power strips, and surge protectors are not allowed inside walls under the National Electrical Code. Use an in-wall power kit in a hollow wall or have a licensed pro add a recessed outlet.

Are in-wall power kits safe?

Yes, when the kit is UL listed and installed as directed in a hollow stud wall. The cable inside the wall is in-wall rated, and the plates are proper electrical boxes. They are not for solid walls.

Can you hide TV wires in a brick or concrete wall?

Yes, but not inside it. Use millwork, a furred wall, a painted cable raceway, or a cut channel with conduit. Or mount the TV above an existing outlet and hide the short cable behind furniture.

How can I hide TV wires without drilling into the wall?

A paintable cable raceway with adhesive backing, cable clips along the baseboard, and a media console placed under the TV. It is not invisible, but it is clean, and it is the renter option.

Will hiding wires in plaster damage the wall?

It makes holes. Done right, the holes sit behind the TV and behind furniture, and a painter finishes the edges. Done wrong, the plaster cracks well past the opening.

How long does it take to mount a TV and hide the wires?

A half day to a full day in plaster. Concrete with millwork is a multi-day project with a carpenter. Add a painter visit after.

Is a soundbar cable hidden the same way?

Yes. The soundbar's HDMI and power cables follow the same path. Many of our clients put the soundbar and TV in one millwork unit so nothing shows. See how we size the screen first in how to choose the right TV.

Want the TV on the wall and nothing else in sight? We will tell you which method fits your wall, coordinate the electrical work and the painter, and hand you an itemized proposal. Start with our home theater installation cost guide or book a free consultation.

About the Author

Mark Feinberg, Founder & CEO of Home Theater Advisors. Before founding HTA in 2011, Mark ran Product Management at ADI, one of the largest AV distributors in the country. He is a Certified Control4 Smart Home Dealer and CEDIA member, and HTA has earned multiple Houzz Best of Design Awards. Mark holds a BA from Dartmouth and an MBA from Duke's Fuqua School of Business. He lives in Manhattan with his family.

A TV on the Wall. Nothing Else.

Plaster, masonry, or glass, we hide the cables the right way. Free consultation, itemized proposal, Upper East Side based.

Call (646) 450-1060 →Book a Free Consultation
blog author avatar
Founder & CEO of Home Theater Advisors. Certified Control4 Dealer, CEDIA member, former ADI Product Management. 500+ NYC installs since 2011.
Back to Blog

© 2025 Home Theater Advisors. All rights reserved.